General Category > Unofficial F/A-18 Acceleration Pack board
Sludge Hornet v2.0
ctec1:
Sludge,
With voice slider @ 100% and all other sound sliders @ 10% Betty is barely audible. ATC is loud and clear. Ive checked my sound card settings as well and everything seems to be set correctly. Herbie says he experienced the same thing and changed the files via wave editor. Maybe its something specific to our systems. I have a Creative SB X-Fi sound card if that helps.
Sludge:
CTEC...
OK, that's what I was looking for. I can make them with much higher default volumes, dont worry about changing the .wav file volumes. I'll get new ones sent out that are 50% higher. I should be able to get that to you by tonight. Or you can do it yourself? In your earlier post, you have open the FA-18 folder with all the .wav files and the Sounds.INI file. If you open the Sounds.INI file with Notepad, you'll see a buncha of values near the bottom and their associated .wav file. The Betty .wavs are -1250, so change them to -650 and see what results you get. As you can see, the gun (M61) .wavs are -450, so that will give you a baseline as to how loud things can get.
Frenchie...
Ahh, I see. Good catch. Yes, you can DELETE the FSX\SOUNDS folder and KEEP the FSX\SOUND folder, as its the default and needs to be there.
Later
Sludge
Herbie:
Herbie...
Hmm, did you install the HotFix.ZIP? If so, it should have the PA-PID.XML disabled so your trim inputs stay without any interference.
Later
Sludge
[/quote]
Installed it just now, thanks. Didn't had it before. Herb
ctec1:
--- Quote from: Sludge on March 11, 2013, 04:43:33 pm ---CTEC...
OK, that's what I was looking for. I can make them with much higher default volumes, dont worry about changing the .wav file volumes. I'll get new ones sent out that are 50% higher. I should be able to get that to you by tonight. Or you can do it yourself? In your earlier post, you have open the FA-18 folder with all the .wav files and the Sounds.INI file. If you open the Sounds.INI file with Notepad, you'll see a buncha of values near the bottom and their associated .wav file. The Betty .wavs are -1250, so change them to -650 and see what results you get. As you can see, the gun (M61) .wavs are -450, so that will give you a baseline as to how loud things can get.
--- End quote ---
Sludge,
Per your instructions I edited the Sounds.ini file. Although the Betty waves are easier to hear now I still believe they are somewhat weak. Can I assume that a setting of -0 would be as loud as the file will play. If so I'm using that setting and still think the volume is a bit too low. Heres whats confusing, The "Over G" file is loud and crisp yet the "pull up" file is faint. Both files are set @ -0 in the ini. I tried using the -650 that you suggested but still get the same results. Just giving you some feedback on the sound issue. Its not stopping me from enjoying your work. Thx again!
Herbie:
Sludge,
Per your instructions I edited the Sounds.ini file. Although the Betty waves are easier to hear now I still believe they are somewhat weak. Can I assume that a setting of -0 would be as loud as the file will play. If so I'm using that setting and still think the volume is a bit too low. Heres whats confusing, The "Over G" file is loud and crisp yet the "pull up" file is faint. Both files are set @ -0 in the ini. I tried using the -650 that you suggested but still get the same results. Just giving you some feedback on the sound issue. Its not stopping me from enjoying your work. Thx again!
[/quote]
Please go up a few Post and see the different between a low sound and the right edited sound. I did amplify by 3 dB most of the Betty Sounds. For me this is the only way. You can double click any sound file in your computer, it should play with windows-player for a test. Herb
Navigation
[0] Message Index
[#] Next page
[*] Previous page
Go to full version