Products Support > GSX Pro - Aircraft profiles

request, maddog MD-82 profile

<< < (2/2)

Jetlover747:

--- Quote from: b742f on January 14, 2023, 12:21:00 am ---
--- Quote from: icebird4all on September 24, 2022, 01:58:08 pm ---try - maybe its ok!

one thing i couldn't get ok was the  aft service door ... since the truck always come from the wrong direction and was going through the  plane - so i deactivate it!

have fun!


--- Code: ---[aircraft]
nosegear = 19.16
refueling = 0
battery = 1
pushbackraise = 1
pushbackdummyevent = 0
pushbackcheckengines = 1
iscargo = 0
trafficcones = 1
preferredexit =  0
wingrootpos = 3.13 -1.07 -0.36
wingtippos = 14.65 -5.61 -0.30
fuelpos = 6.87 -1.98 -0.85
waterpos = -1.25 -10.50 -0.41
lavatorypos = -1.25 -11.24 -0.67
gpupos = 1.30 23.80 -2.11
bypasspinpos = -0.01 19.18 -1.93
engine1pos = -2.57 -11.61 0.27
engine2pos = 2.58 -11.73 0.27
engine3pos = 0.00 0.00 0.00
engine4pos = 0.00 0.00 0.00

[exit1]
pos = -1.21 16.96 -0.23 1.00
code = 1
name = FWD cabin door
embeddedStair = -1.83 16.98 -0.23 -3.68 16.89 -2.67

[exit2]
remove = 1

[exit3]
remove = 1

[exit4]
pos = -0.01 -12.74 -0.21 -90.00
code = (L:aft_stair_MD, number) 0 !=
name = Rear Exit (requires Hydraulic Press)
embeddedStair = -0.01 -13.24 -0.21 0.00 -15.60 -2.61

[service1]
pos = 1.59 17.04 -0.48 -1.00
code = 2
name = FWD galley door
embeddedStair = 0

[service2]
remove = 1

[cargo1]
pos = 0.51 11.85 -1.47 2.00
code = 3
name = FWD cargo door
embeddedStair = 0
uldcode = AUTO

[cargo2]
pos = 0.52 -7.95 -1.43 4.00
code = 4
name = AFT cargo door
embeddedStair = 0
uldcode = AUTO

[cargomain]
pos = 0.69 5.05 -1.49 0.00
code = 1
name = FWD galley door
embeddedStair = 0
uldcode = AUTO
--- End code ---

--- End quote ---

Thanks! The one thing I find is the baggage loaders not opening the cargo doors. They load with doors closed

--- End quote ---

For your previous query about the aft service door - one, is it really a service door? I thought it was just an emergency exit. and two, it's rotated the wrong way. Open the gsx aircraft editor, select that door and hit F8 a few times until it is in the right direction. You want the bottom pad facing away from the door - not in the fuselage.

cconesa:
I found a strange issue with the Md83/Md88 expansions. When pushing back one of those two aircraft, the pushback person goes to the middle of the aircraft (wing root) to connect the bypass pin... Other than that, it all works fine but is that one thing that is off. Any ideas as to why that happens?.

Jetlover747:

--- Quote from: cconesa on March 31, 2023, 02:25:29 pm ---I found a strange issue with the Md83/Md88 expansions. When pushing back one of those two aircraft, the pushback person goes to the middle of the aircraft (wing root) to connect the bypass pin... Other than that, it all works fine but is that one thing that is off. Any ideas as to why that happens?.

--- End quote ---
MD-83 and MD-88 don't have internal gsx profiles iirc, therefore you'll have to find a profile or manually customize pin location for it to not just be autoset to the middle of the aircraft (wing root).

Navigation

[0] Message Index

[*] Previous page