Products Support > GSX Pro - Aircraft profiles
request, maddog MD-82 profile
motishow:
Anyone can share a good profile for Maddog ?
thanks
icebird4all:
try - maybe its ok!
one thing i couldn't get ok was the aft service door ... since the truck always come from the wrong direction and was going through the plane - so i deactivate it!
have fun!
--- Code: ---[aircraft]
nosegear = 19.16
refueling = 0
battery = 1
pushbackraise = 1
pushbackdummyevent = 0
pushbackcheckengines = 1
iscargo = 0
trafficcones = 1
preferredexit = 0
wingrootpos = 3.13 -1.07 -0.36
wingtippos = 14.65 -5.61 -0.30
fuelpos = 6.87 -1.98 -0.85
waterpos = -1.25 -10.50 -0.41
lavatorypos = -1.25 -11.24 -0.67
gpupos = 1.30 23.80 -2.11
bypasspinpos = -0.01 19.18 -1.93
engine1pos = -2.57 -11.61 0.27
engine2pos = 2.58 -11.73 0.27
engine3pos = 0.00 0.00 0.00
engine4pos = 0.00 0.00 0.00
[exit1]
pos = -1.21 16.96 -0.23 1.00
code = 1
name = FWD cabin door
embeddedStair = -1.83 16.98 -0.23 -3.68 16.89 -2.67
[exit2]
remove = 1
[exit3]
remove = 1
[exit4]
pos = -0.01 -12.74 -0.21 -90.00
code = (L:aft_stair_MD, number) 0 !=
name = Rear Exit (requires Hydraulic Press)
embeddedStair = -0.01 -13.24 -0.21 0.00 -15.60 -2.61
[service1]
pos = 1.59 17.04 -0.48 -1.00
code = 2
name = FWD galley door
embeddedStair = 0
[service2]
remove = 1
[cargo1]
pos = 0.51 11.85 -1.47 2.00
code = 3
name = FWD cargo door
embeddedStair = 0
uldcode = AUTO
[cargo2]
pos = 0.52 -7.95 -1.43 4.00
code = 4
name = AFT cargo door
embeddedStair = 0
uldcode = AUTO
[cargomain]
pos = 0.69 5.05 -1.49 0.00
code = 1
name = FWD galley door
embeddedStair = 0
uldcode = AUTO
--- End code ---
Dal123:
The latest firmware update from MadDog has built in option for GSX. it works great!
cyrax87:
No it doesnt.
The rear stairs are bvroken. As soon as I hit the live updater it breaks the profile again and the passengers boarding throgh the rear are launched up in the air and stay there.
I wonder why the heck noone fixes this. There are numerous profiles around that work perfectly fine.
It is extremely annoying to constantly replace the profile manually becaus the actual installer breaks it over and over again...
b742f:
--- Quote from: icebird4all on September 24, 2022, 01:58:08 pm ---try - maybe its ok!
one thing i couldn't get ok was the aft service door ... since the truck always come from the wrong direction and was going through the plane - so i deactivate it!
have fun!
--- Code: ---[aircraft]
nosegear = 19.16
refueling = 0
battery = 1
pushbackraise = 1
pushbackdummyevent = 0
pushbackcheckengines = 1
iscargo = 0
trafficcones = 1
preferredexit = 0
wingrootpos = 3.13 -1.07 -0.36
wingtippos = 14.65 -5.61 -0.30
fuelpos = 6.87 -1.98 -0.85
waterpos = -1.25 -10.50 -0.41
lavatorypos = -1.25 -11.24 -0.67
gpupos = 1.30 23.80 -2.11
bypasspinpos = -0.01 19.18 -1.93
engine1pos = -2.57 -11.61 0.27
engine2pos = 2.58 -11.73 0.27
engine3pos = 0.00 0.00 0.00
engine4pos = 0.00 0.00 0.00
[exit1]
pos = -1.21 16.96 -0.23 1.00
code = 1
name = FWD cabin door
embeddedStair = -1.83 16.98 -0.23 -3.68 16.89 -2.67
[exit2]
remove = 1
[exit3]
remove = 1
[exit4]
pos = -0.01 -12.74 -0.21 -90.00
code = (L:aft_stair_MD, number) 0 !=
name = Rear Exit (requires Hydraulic Press)
embeddedStair = -0.01 -13.24 -0.21 0.00 -15.60 -2.61
[service1]
pos = 1.59 17.04 -0.48 -1.00
code = 2
name = FWD galley door
embeddedStair = 0
[service2]
remove = 1
[cargo1]
pos = 0.51 11.85 -1.47 2.00
code = 3
name = FWD cargo door
embeddedStair = 0
uldcode = AUTO
[cargo2]
pos = 0.52 -7.95 -1.43 4.00
code = 4
name = AFT cargo door
embeddedStair = 0
uldcode = AUTO
[cargomain]
pos = 0.69 5.05 -1.49 0.00
code = 1
name = FWD galley door
embeddedStair = 0
uldcode = AUTO
--- End code ---
--- End quote ---
Thanks! The one thing I find is the baggage loaders not opening the cargo doors. They load with doors closed
Navigation
[0] Message Index
[#] Next page
Go to full version