Products Support > GSX Sharing area - Airplane Configs
CS 777-200/300
virtuali:
--- Quote from: Guy1300 on May 10, 2013, 07:54:30 pm ---question when is the 300s will can be use too?
--- End quote ---
You can create a configuration for it with the GSX editor. However, since those airplanes use non-standard doors, they might be difficult to figure it out their XML variables.
But you can use the method explained here, using the 200 as a "template":
http://www.fsdreamteam.com/forum/index.php?topic=8147.msg66851#msg66851
--- Quote ---If you use the 300 version, is not included with the GSX database but, assuming it use the same variables, one way to customize it correctly without having to Ignore a door (which must work), is to load the 200 version, customize something not important (such as moving a door 1-2 cm) and than take the GSX.INI that will be created into %APPDATA%\Virtuali\Airplanes, and move it into the ROOT folder under FSX\Simobjects\Airplanes for the 300 version.
Then, load the 300 version, and this will load the 200 customization with the XML variables and custom names, so you'll only need to adjust their position for the different 300 size.
--- End quote ---
Guy1300:
--- Quote from: virtuali on May 10, 2013, 10:34:07 pm ---
--- Quote from: Guy1300 on May 10, 2013, 07:54:30 pm ---question when is the 300s will can be use too?
--- End quote ---
You can create a configuration for it with the GSX editor. However, since those airplanes use non-standard doors, they might be difficult to figure it out their XML variables.
But you can use the method explained here, using the 200 as a "template":
http://www.fsdreamteam.com/forum/index.php?topic=8147.msg66851#msg66851
--- Quote ---If you use the 300 version, is not included with the GSX database but, assuming it use the same variables, one way to customize it correctly without having to Ignore a door (which must work), is to load the 200 version, customize something not important (such as moving a door 1-2 cm) and than take the GSX.INI that will be created into %APPDATA%\Virtuali\Airplanes, and move it into the ROOT folder under FSX\Simobjects\Airplanes for the 300 version.
Then, load the 300 version, and this will load the 200 customization with the XML variables and custom names, so you'll only need to adjust their position for the different 300 size.
--- End quote ---
--- End quote ---
Thanks for reply but where can I find the GSX editor?
virtuali:
--- Quote from: Guy1300 on May 11, 2013, 09:46:01 am ---Thanks for reply but where can I find the GSX editor?
--- End quote ---
It comes within the program, the change aircraft configuration menu option of the Couatl menu. I suggest having a look at the GSX manual too.
Guy1300:
--- Quote from: virtuali on May 11, 2013, 11:30:12 am ---
--- Quote from: Guy1300 on May 11, 2013, 09:46:01 am ---Thanks for reply but where can I find the GSX editor?
--- End quote ---
It comes within the program, the change aircraft configuration menu option of the Couatl menu. I suggest having a look at the GSX manual too.
--- End quote ---
np thanks ill try and ill back with results :)
okupton:
I like to know how to get this set up correctly as well. Well, everything is working well except there aren't the usual three baggage carts connected to each tug but only one. So boarding and deboarding takes about 1 minute as GEX isnt recognizing that this is a heavy aircraft. It's treating it almost like it were a cessna.
Navigation
[0] Message Index
[#] Next page
[*] Previous page
Go to full version