Products Support > GSX Support FSX/P3D
Does Anyone Know Why my Plane is Spinning Out of Control in Slew Mode in FSX?
kmanning:
--- Quote from: virtuali on September 14, 2022, 12:29:16 am ---
--- Quote from: kmanning on September 13, 2022, 11:55:41 pm ---Here's what I did to solve this problem:
On the left side under Controls, select Axis Assignments. At the top where it says Controller, select your TCA Throttle Quadrent. It should say TCA Q-Eng 1&2. Next to Flight Mode, select Slew. Scroll down and delete the assignments that are shown in the attached image:
--- End quote ---
That's exactly what I said it should be done:
--- Quote ---You shouldn't disable a controller but, instead, remove its axes from SLEW MODE ( only! )
--- End quote ---
--- End quote ---
Hi Umberto,
Thanks so much for clearing this up. I guess my instructions that I've posted is correct. The thing is that every time I hear someone say to remove the axis from the the Slew Mode, I've always had the understanding that everyone was referring to the Buttons tab and there is an assignment for the Y Key that puts the sim into slew mode. That was the only thing I knew that was related to slew. Then I happen to noticed that there were 2 buttons, one for normal mode and the other for slew mode, but no one never brought that up and I just over looked it. I've never knew until a few days ago that there's a Slew mode button and I don't know why I haven't noticed it before until all of this came up. Well, for one thing, I had no reason to use it before.
Ken.
bhorv67:
I'd still like to know what changed recently that this suddenly became a problem to have controller axis assigned to slew.
My P3d config hasn't changed in years.
Captain Kevin:
--- Quote from: bhorv67 on September 16, 2022, 01:33:15 am ---I'd still like to know what changed recently that this suddenly became a problem to have controller axis assigned to slew.
My P3d c/onfig hasn't changed in years.
--- End quote ---
Controller got old and can start having spikes that cause this?
cirurgiao:
--- Quote from: virtuali on September 13, 2022, 11:38:38 pm ---
--- Quote from: trisho0 on September 13, 2022, 04:42:19 pm ---Ken, disabling the FSX Controllers I can't do panning views. From keyboard the Spacer bar has no responses. Can you change Views
--- End quote ---
You shouldn't disable a controller but, instead, remove its axes from SLEW MODE ( only! )
--- End quote ---
I really don't know how to (if possible) to disable Slew Mode and where to find it.
Anyway I have the same trouble (spining acft) while trying to create jetways through GSX in Technobrain's RJTT. Its support answered my question that 1) jetways only with CTRL+J & 2) No GSX or SODEs. Since I didn't try to create jetways through GSX in other scenery can't say if it's scenery related.
trisho0:
--- Quote from: cirurgiao on September 18, 2022, 02:27:47 pm ---
--- Quote from: virtuali on September 13, 2022, 11:38:38 pm ---
--- Quote from: trisho0 on September 13, 2022, 04:42:19 pm ---Ken, disabling the FSX Controllers I can't do panning views. From keyboard the Spacer bar has no responses. Can you change Views
--- End quote ---
You shouldn't disable a controller but, instead, remove its axes from SLEW MODE ( only! )
--- End quote ---
I really don't know how to (if possible) to disable Slew Mode and where to find it.
Anyway I have the same trouble (spining acft) while trying to create jetways through GSX in Technobrain's RJTT. Its support answered my question that 1) jetways only with CTRL+J & 2) No GSX or SODEs. Since I didn't try to create jetways through GSX in other scenery can't say if it's scenery related.
--- End quote ---
Please, check my picture named FSX Axis posted in this thread. Find it and you are good to continue.
Patricio Valdes
Navigation
[0] Message Index
[#] Next page
[*] Previous page
Go to full version