Products Support > GSX Support FSX/P3D
Does Anyone Know Why my Plane is Spinning Out of Control in Slew Mode in FSX?
trisho0:
--- Quote from: virtuali on September 13, 2022, 11:38:38 pm ---
--- Quote from: trisho0 on September 13, 2022, 04:42:19 pm ---Ken, disabling the FSX Controllers I can't do panning views. From keyboard the Spacer bar has no responses. Can you change Views
--- End quote ---
You shouldn't disable a controller but, instead, remove its axes from SLEW MODE ( only! )
--- End quote ---
Do I have to disable all Slew Axis presented in this posted image? I will have to do the same for P3Dv4 and P3Dv5 as well.
Pat
kmanning:
--- Quote from: trisho0 on September 14, 2022, 12:13:32 am ---
--- Quote from: virtuali on September 13, 2022, 11:38:38 pm ---
--- Quote from: trisho0 on September 13, 2022, 04:42:19 pm ---Ken, disabling the FSX Controllers I can't do panning views. From keyboard the Spacer bar has no responses. Can you change Views
--- End quote ---
You shouldn't disable a controller but, instead, remove its axes from SLEW MODE ( only! )
--- End quote ---
Do I have to disable all Slew Axis presented in this posted image? I will have to do the same for P3Dv4 and P3Dv5 as well.
Pat
--- End quote ---
Hi
Umberto just posted what to do the solve this problem at about the same time I posted mine. Yes, I've deleted all 3 of them but make sure you click delete JOYSTICK assignments. I've replied to Umberto about this and you might want to wait until he replies to my question. It this is not what Umberto is referring to or he says it's not correct, I will take this down.
Ken.
virtuali:
--- Quote from: kmanning on September 13, 2022, 11:55:41 pm ---Here's what I did to solve this problem:
On the left side under Controls, select Axis Assignments. At the top where it says Controller, select your TCA Throttle Quadrent. It should say TCA Q-Eng 1&2. Next to Flight Mode, select Slew. Scroll down and delete the assignments that are shown in the attached image:
--- End quote ---
That's exactly what I said it should be done:
--- Quote ---You shouldn't disable a controller but, instead, remove its axes from SLEW MODE ( only! )
--- End quote ---
virtuali:
--- Quote from: trisho0 on September 14, 2022, 12:13:32 am ---Do I have to disable all Slew Axis presented in this posted image? I will have to do the same for P3Dv4 and P3Dv5 as well
--- End quote ---
You should do this for *every* controller you have. Especially if you have some you don't normally use for flying, those are the ones easy to forget, that are usually left not calibrated, and always caused this problem.
And yes, you should do that for FSX and P3D.
trisho0:
--- Quote from: virtuali on September 14, 2022, 12:31:56 am ---
--- Quote from: trisho0 on September 14, 2022, 12:13:32 am ---Do I have to disable all Slew Axis presented in this posted image? I will have to do the same for P3Dv4 and P3Dv5 as well
--- End quote ---
You should do this for *every* controller you have. Especially if you have some you don't normally use for flying, those are the ones easy to forget, that are usually left not calibrated, and always caused this problem.
And yes, you should do that for FSX and P3D.
--- End quote ---
All SLEW Axis settings removed, and plane doesn't spin anymore, good! But still the same Jetway's Bridge dropping with editing in all FSX, P4D and P5D.
Pat
Navigation
[0] Message Index
[#] Next page
[*] Previous page
Go to full version