Products Support > GSX Support FSX/P3D

A2A Constellation

<< < (2/3) > >>

ianfisher:
Here you go.


[aircraft]
nosegear = 9.42
refueling = 1
battery = 1
iscargo = 0
trafficcones = 1
preferredexit =  0
wingrootpos = 2.37 -0.83 0.81
wingtippos = 17.70 -1.87 1.93
fuelpos = 11.82 -1.33 0.84
waterpos = 0.00 0.00 0.00
lavatorypos = 0.00 0.00 0.00
engine1pos = -9.10 2.26 0.45
engine2pos = -4.31 2.84 -0.13
engine3pos = 4.31 2.84 -0.13
engine4pos = 9.10 2.26 0.45

[exit1]
pos = -1.42 -7.86 0.53 0.00
code = 1
name = Exit 1
embeddedStair = -2.42 -7.83 0.22 -4.94 -8.22 -2.71

[exit2]
remove = 1

[exit3]
remove = 1

[exit4]
remove = 1

[service1]
pos = 1.66 -7.81 -0.69 -0.00
code = 0
embeddedStair = 0

[service2]
remove = 1

[cargo1]
pos = 0.30 6.08 -1.86 0.00
code = 2
name = Exit 2
embeddedStair = 0
uldcode = AUTO

[cargo2]
pos = 0.44 -5.07 -1.09 0.00
code = 2
name = Exit 2
embeddedStair = 0
uldcode = AUTO

[cargomain]
remove = 1

C130:

--- Quote from: virtuali on February 06, 2020, 11:41:43 am ---Try to disable the "Estimate passenger number" option in GSX, and set the number of passengers manually.

--- End quote ---

Did that and no effect.

I get a message in red text "there are no passenger stairs you will not see any passengers boarding".

In the GSX Customizer, the Disable staircases is unticked, yet there are no Staircases to edit at the gate?

Something is blocking the staircases from being initialised in GSX?

I tried the Aircraft customisation with the parameters for embedded stairs, this had no effect.

Still stuck!

Regards
David

EDIT The passenger bus arrives, with passengers on it. No boarding takes place. Its as if GSX 2 wont work with the A2A Connie????

C130:

--- Quote from: ianfisher on February 06, 2020, 02:21:20 pm ---There is a profile for this in the Fourms

--- End quote ---

That's interesting. The photo shows a GSX Stairway and not the embedded A2A Stairway and Stewardess that comes with the Connie.

So you disable the A2A Stairway from the A2A menu. The GSX stairs should then show up. My problem is that no GSX stairs are available with the A2A Connie, even in the edit airport positions editor?

It's as if the Connie is blocking GSX stairs from appearing.

I have tried at several airports and get the same results. So it's not the airports.

As your photo shows its frustrating! ???

Regards
David

C130:
Partially resolved!!

OK so what I did was as follows(may help anyone else who experienced my issue)


Copy and paste the GSX cfg, from ianfisher, into your GSX aircraft folder.
GSX menu manually select number of passengers.
Shift+3 A2A menu, enable A2A stairs. (need these because GSX stairs will not appear (for me?)
Shift+4 A2A load aircraft menu with max passenger load.
from GSX menu select Boarding.
when A2A boarding completes early Shift+4 again . ( A2A boarding finishes early and stairs move before GSX passengers have finished boarding.)
Boarding completes.

I have attached some pictures.

I don't understand why I cant get any GSX stairways to show, but using the above method allows GSX2 boarding using the A2A stairs!

Cheers!

trisho0:

--- Quote from: ianfisher on February 06, 2020, 02:23:41 pm ---Here you go.


[aircraft]
…………..

--- End quote ---
Where do you copy/paste this contents?

Navigation

[0] Message Index

[#] Next page

[*] Previous page