« previous next »
Pages: [1]

Author Topic: T-45 HUD problem ...  (Read 8910 times)

average_joe

  • Newbie
  • *
  • Posts: 29
T-45 HUD problem ...
« on: March 30, 2010, 02:40:33 am »
When I get airborne and cleaned up, the velocity vector and pitch ladder is offset quite a ways towards the left edge of the HUD. I can bring it back to center by inputting a lot of right rudder (except now I'm doing rudder rolls).

Checked the controller - calibration is ok.
Logged

Stretch32

  • Newbie
  • *
  • Posts: 13
Re: T-45 HUD problem ...
« Reply #1 on: March 30, 2010, 03:02:01 am »
Sounds like the HUD is uncaged. There's a key command that will cage it and set the pitch ladder in the middle of the HUD although I'm not sure what it is. If you've got the realistic HUD I think it's in the readme that came with it.

Stretch
Logged

Razgriz

  • Hero Member
  • *****
  • Posts: 699
Re: T-45 HUD problem ...
« Reply #2 on: March 30, 2010, 03:05:54 am »
Quote from: average_joe on March 30, 2010, 02:40:33 am
When I get airborne and cleaned up, the velocity vector and pitch ladder is offset quite a ways towards the left edge of the HUD. I can bring it back to center by inputting a lot of right rudder (except now I'm doing rudder rolls).

Checked the controller - calibration is ok.

Caused by wind.  Cage your hud and you will have a ghost velocity vector where it is now, and the normal velocity vector centered along with the pitch ladder.
Logged

average_joe

  • Newbie
  • *
  • Posts: 29
Re: T-45 HUD problem ...
« Reply #3 on: March 30, 2010, 03:51:01 am »
Readme file mentions a cage "switch". Don't see any such switch in the VC view.

Winds were light at 5000'. Crab angle shouldn't be that "big" a factor. I think the F-18 HUD limit is 8 degrees ... need big winds for that much crab at 300 knots!

Thanks
Logged

Stretch32

  • Newbie
  • *
  • Posts: 13
Re: T-45 HUD problem ...
« Reply #4 on: March 30, 2010, 05:01:59 am »
T-45C cage switch is on the stick about halfway down the grip on the left side (where your thumb would rests if you were just holding it). I don't know if you can click it or if it's even modeled though.

Stretch
Logged

wilycoyote4

  • Full Member
  • ***
  • Posts: 225
Re: T-45 HUD problem ...
« Reply #5 on: March 30, 2010, 07:08:26 am »
The cage switch for this FSX aircraft is on a popup panel.  Press shift+5.

This is for the improved realistic HUD resized fot the Goshawk.  Not Dino's default.
« Last Edit: March 30, 2010, 07:26:47 am by wilycoyote4 »
Logged

Stretch32

  • Newbie
  • *
  • Posts: 13
Re: T-45 HUD problem ...
« Reply #6 on: March 31, 2010, 06:01:02 am »
Where do you find this HUD at? At one point I had it but can't seem to find it anymore after reloading FSX.

Stretch
Logged

Orion

  • Hero Member
  • *****
  • Posts: 753
Re: T-45 HUD problem ...
« Reply #7 on: March 31, 2010, 06:05:58 am »
Quote from: Stretch32 on March 31, 2010, 06:01:02 am
Where do you find this HUD at? At one point I had it but can't seem to find it anymore after reloading FSX.

Stretch
That would be Jivko Rusev (neutrino)'s improved FA-18 HUD adapted for Dino's T-45 Goshawk ;).

Get it here: http://www.simviation.com/simviation/?ID=7266.
Logged
Pages: [1]
« previous next »