FSDreamTeam forum

Products Support => GSX Support FSX/P3D => GSX Sharing area - Airplane Configs => Topic started by: djfabio69 on August 25, 2013, 12:20:16 pm

Title: Aerosoft Twin Otter Extended
Post by: djfabio69 on August 25, 2013, 12:20:16 pm

Hello, has anyone a config for this aircraft?

Many thanks

Title: Re: Aerosoft Twin Otter Extended
Post by: theonlyrex on October 29, 2015, 05:58:46 pm

Bump

Title: Re: Aerosoft Twin Otter Extended
Post by: jorjys on May 13, 2017, 12:35:35 am

Bump???!!

Title: Re: Aerosoft Twin Otter Extended
Post by: stripealipe on June 11, 2017, 06:55:27 pm

Would love one for this aircraft too. Amazed it's not supported out of the box... thanks!

Title: Re: Aerosoft Twin Otter Extended
Post by: 7heAngryVe7eran on July 11, 2017, 01:57:32 pm

I have this aircraft and not really sure what there is to configure. This aircraft is not normally pushed back or loaded with any sort of belt or assistance. What exactly are you guys wanting configured?

Title: Re: Aerosoft Twin Otter Extended
Post by: Kilstorm on October 05, 2018, 01:48:01 am

Quote from: JackRiordan on July 11, 2017, 01:57:32 pm

I have this aircraft and not really sure what there is to configure. This aircraft is not normally pushed back or loaded with any sort of belt or assistance. What exactly are you guys wanting configured?

With GSX level 2 out now it would be great to configure the passenger door for crew and pax.

Title: Re: Aerosoft Twin Otter Extended
Post by: qqwertz on October 07, 2018, 03:39:23 pm

I had a look at it, but it doesn't make sense for this plane. The cargo doors do indeed look strange with a belt at it, and entry door and cabin are not very high. Passengers would have to bend to properly go through it, but that's not implemented in GSX2.

Peter

Title: Re: Aerosoft Twin Otter Extended
Post by: Kilstorm on October 07, 2018, 06:57:06 pm

Quote from: qqwertz on October 07, 2018, 03:39:23 pm

I had a look at it, but it doesn't make sense for this plane. The cargo doors do indeed look strange with a belt at it, and entry door and cabin are not very high. Passengers would have to bend to properly go through it, but that's not implemented in GSX2.

Peter

That said, would you be able to make a template for the twin Otter? I never go outside the cockpit to watch the pax and cargo board but can see the buses from the pilot window. It would be nice to look back and see pax walking to the plane instead of a bus pull up, doors open, doors close and leave. I was able to get the cargo to load to the service door on the co-pilot side of the plane but for some reason cant figure out how to assign the stairs for pax loading.

Title: Re: Aerosoft Twin Otter Extended
Post by: qqwertz on October 08, 2018, 07:47:58 pm

OK, here you go (for the -300 variant). Just don't complain that it looks funny  ;D

[aircraft]
nosegear = 3.92
refueling = 1
battery = 1
iscargo = 0
trafficcones = 1
preferredexit =  0
wingrootpos = 0.99 -0.49 0.08
wingtippos = 9.16 -0.25 0.34
fuelpos = 4.00 -0.00 -0.19
waterpos = -0.00 -0.00 -0.50
lavatorypos = 0.00 0.00 0.00
engine1pos = -2.79 1.13 -0.06
engine2pos = 2.79 1.38 -0.06
engine3pos = 0.00 0.00 0.00
engine4pos = 0.00 0.00 0.00

[exit1]
pos = -0.69 -2.35 -1.62 -3.90
code = 1
name = Passenger door
embeddedStair = 0

[exit2]
remove = 1

[exit3]
remove = 1

[exit4]
remove = 1

[service1]
remove = 1

[service2]
remove = 1

[cargo1]
pos = 0.67 -2.45 -1.61 3.10
code = 2
name = Right cargo door
embeddedStair = 0
uldcode = BELT

[cargo2]
remove = 1

[cargomain]
remove = 1

Title: Re: Aerosoft Twin Otter Extended
Post by: Kilstorm on October 08, 2018, 09:25:18 pm

Thank you. Got it to work.