FSDreamTeam forum

Products Support => GSX Support FSX/P3D => GSX Sharing area - Scenery Configs => Topic started by: Juergen2 on June 20, 2020, 01:22:46 pm

Title: Cartayna AS EGLL No Jetways
Post by: Juergen2 on June 20, 2020, 01:22:46 pm

Hi,
I just installed the Cartayna "EGLL-Heathrow (V5) AS Professional with the following options: EGLL logo Glass>with Europier>Both Rways.
I restarted Cuoatl and rebuild airport cache 3 times -absolutely NO jetways show up.
Any help would be appreciated.
Thanks
Juergen Mader

Title: Re: Cartayna AS EGLL No Jetways
Post by: virtuali on June 25, 2020, 02:55:02 pm

You don't say which simulator you use.

Title: Re: Cartayna AS EGLL No Jetways
Post by: Juergen2 on June 25, 2020, 03:03:30 pm

Hi,
Sorrry, I am using P3Dv4.
Thanks
Juergen Mader

Title: Re: Cartayna AS EGLL No Jetways
Post by: virtuali on June 25, 2020, 03:04:33 pm

Which AFCAD is in use by GSX ? You can check this in the scenery customization page. Is the AFCAD in use by GSX the correct one for that .INI file ? You can check this in the [General] section of the .INI file itself.

Title: Re: Cartayna AS EGLL No Jetways
Post by: Juergen2 on June 25, 2020, 03:11:49 pm

Umberto,
I will check this afternoon and reply.
Thanks again in trying to resolve the ongoing jetway saga
Juergen Mader

Title: Re: Cartayna AS EGLL No Jetways
Post by: Juergen2 on June 25, 2020, 09:37:26 pm

Umberto,
I loaded a flight in EGLL and had to leave the PC for a few minutes. When I returned, all jetbridges were available. It could be that I didn't wait long enough for the airport cache to reload when the jet bridges didn't load.
I also checked the AFCAD as specified in GSX customization page and it is the same as specified in the General section of the "egll-cartayna-EUROPIERv5GLASS.ini file.
So all is well in London.
Thanks for your hint, I will try the same in KTPA
Thanks
Juergen Mader

Title: Re: Cartayna AS EGLL No Jetways
Post by: virtuali on June 26, 2020, 11:04:08 am

Quote from: Juergen2 on June 25, 2020, 09:37:26 pm

I loaded a flight in EGLL and had to leave the PC for a few minutes. When I returned, all jetbridges were available. It could be that I didn't wait long enough for the airport cache to reload when the jet bridges didn't load.

In general, you shouldn't always recreate the airport cache manually.

The only case in which you must do that, is when a 3rd party scenery that comes with a configuration utility that switches between different AFCAD for the same airport using file *renaming* and that cannot always detected by GSX automatically but, in normal use, rebuilding the cache is not required.

And, to minimize the airport cache rebuild time, add the simulator own folder ( and if you have sceneries installed outside of it, add their own folders too ) to the antivirus Exclusion list. This can make for a huge difference in the cache rebuild time, when needed.

Title: Re: Cartayna AS EGLL No Jetways
Post by: Juergen2 on June 26, 2020, 11:45:01 am

Thanks a lot Umberto, will do the exclusions.
Juergen

Title: Re: Cartayna AS EGLL No Jetways
Post by: AleksanderB on August 13, 2020, 12:43:49 pm

I have the same problem with no jetways showing up.

I use P3dv5 and Simwings EGLL v.2.0.0.0.1
In the EGLL configurator, there is no longer an option of the Europier. This might screw up the GSX file?