FSDreamTeam forum
Products Support => GSX Support FSX/P3D => Topic started by: jacques36 on August 11, 2023, 03:38:51 pm
-
Bonjour,
Je n'arrive pas à faire fonctionner correctement GSX Level 2 lorsque je souhaite customiser un emplacement de parking;
Avec la touche f4 j'arrive bien à voir les différents points à customiser mais impossible de les faire avancer, reculer...
On m'a dit que c'étaient les touches Shift+les flèches dir. Pour les bouger ainsi que Shift+1ou3 pour tourner.
Mais rien n'y fait ??
Si quelqu'un peut m'aider, merci d'avance.
-
Only talk in English! Understand?
Translation:
Good morning,
I can't get GSX Level 2 to work properly when I want to customize a parking slot;
With the F4 key I can see the different points to customize but impossible to move them forward, backward...
I was told it was Shift + Dir arrows. To move them as well as Shift+1 or 3 to rotate.
But nothing works??
If anyone can help me, thanks in advance.
-
Check the key assignments for the slew commands since this is what it's using. If you changed any of them, that's why they don't work.
-
Bonjour,
Merci de ton aide, si je comprends bien je dois supprimer toutes les affectations du pavé numérique même celles d'origine sur fsx (phares atterrissage vers la droite, la gauche etc...).
ou bien celle que j'ai affecté perso touche 2 pav numérique pour Ezdock ?
-
I said to speak in English only!
Translation:
Good morning, Thank you for your help; if I understand correctly, do I have to remove all the assignments of the numeric keypad even those of original on FSX (landing lights to the right, the left etc...). or the one that I assigned personal key 2 numeric keypad for EZDok?
-
If you changed any of the key assignments for slew mode, you want to change them back to default.
-
Good morning,
what are the keys for scanning? Those of the numeric keypad only?
Thanks for your help.
-
I'm not sure what you mean by scanning.
-
:(In your previous post you tell me to check the key assignments for the swipe commands because that's what it uses.
What are these keys, again thank you for your help
-
I'm not sure what swipe commands are, either. If you go into the key assignments for P3D, check the assignments for slew mode, or just to be safe, just go there and reset it to default. It should put it back to where it was. But looking back at the translation of the original post, I don't know why you were pushing Shift, either. You didn't need to do that.
-
Good morning,
Unable to get GSX Level2 to work properly.
I no longer have any keys on the numeric keypad assigned. I can't move the different vehicles around the plane with the arrow keys. If someone can give me the solution thank you in advance.
-
I no longer have any keys on the numeric keypad assigned.
That's exactly your problem. I didn't tell you to delete them. I told you to reset them to default. There should be a button in the control assignments that says reset to default.
-
Good morning,
I reset the commands in parameters/commands (restore default parameters) but still impossible to move objects forward, backward on the tarmak. When I use the numpad keys (2, 3, 4....) I just have the view of the plane moving from right to left?. F4 works well when going from object to object.
the keys (2,3,4.....) of the numeric keypad are assigned to various functions in the settings / key buttons. Thank you once again for your help.
-
Just to clarify, the Num Lock key is OFF?
-
Oui la touche Verr Num est bien désactivée et rien ne bouge
-
Toujours pas trouvé la solution.....impossible de déplacer les objets sur le tarmac.
Si quelqu'un peut m'aider à résoudre ce problème, merci d'avance.
-
Did I not tell you to speak in English only?
Translation:
Yes the Num Lock key is disabled and nothing moves
still not found the solution.....impossible to move the objects on the tarmac. If anyone can help me solve this problem, thanks in advance.
-
Still not found the solution.....impossible to move the objects on the tarmac.
If anyone can help me solve this problem, thanks in advance.
-
Good morning,
I think I have a real problem with GSX, now I have passengers walking around on the tarmac.....
I believe I will completely uninstall and reinstall GSX. Is this the solution?
-
Good morning,
I think I have a real problem with GSX, now I have passengers walking around on the tarmac.....
I believe I will completely uninstall and reinstall GSX. Is this the solution?
No, uninstalling and installing again will take a longer time.
-
But then what solution please?
-
Going back over ground already covered:
It sounds like to me, that your keyboard assignments, in P3d Options>Controls, are either incorrect or missing. (I deleted mine and had to re-assign them with Kevin's help)
When you re-assign them on your full-size keyboard, make sure that your NumLock is activated. You need to re-assign (or check that they have been assigned) for: 1,2,3,4,5,6,7,8, and 9 into the P3d Yaw mode assignments. Along with F4, F6, and Y.
Regarding passengers walking around on the tarmac. I think you have accidently assigned feature that for the gate you are at. Personally, I would look at the full file name, up the top, and go in and delete that specific airport file and start again.
Assie
-
Good morning,
First of all thank you for your help.
First I'm on FSX.
In Parameters/Commands I have all the keys of the numeric keypad assigned (Governors).
Should I delete them?
If so how do I reassign with the full size keyboard?
FYI, I have the numeric keys on the full-size keyboard dedicated to ezdok v3 views, but I don't think it should be a problem to assign these views to other keys.
Thank you again for your help.
-
:(Good morning
Having tried different manipulations for several days but I still have no results, I cannot move the objects on the tarmac.
I'm on FSX first.
In Settings/Commands, all keys on the number pad are assigned.
Should I delete them?
Australian 123 told me about reassigning the move functions with the full size keyboard.
How to do ?
FYI, I have the number keys on the full size keyboard dedicated to ezdok v3 views, but I don't think it should be a problem to assign those views to other keys.
Thank you again for your help.