FSDreamTeam forum

Products Support => GSX Support FSX/P3D => Topic started by: doksas on October 08, 2019, 07:58:59 pm

Title: Flight1 ATR 72-500
Post by: doksas on October 08, 2019, 07:58:59 pm

Configuration file for this aircraft please?
Sharing area not have

Title: Re: Flight1 ATR 72-500
Post by: doksas on October 10, 2019, 01:37:58 am

Ok, i configure for now passengers and cargo doors and work great, i want try service door but Flight1 ATR have only two doors, later i will try assign service door on passenger door if possible.

Here is config for visible passengers and baggage:

[aircraft]
nosegear = 8.84
refueling = 1
battery = 1
pushbackraise = 1
pushbackdummyevent = 0
iscargo = 0
trafficcones = 1
preferredexit =  3
wingrootpos = 1.35 -2.69 1.83
wingtippos = 13.44 -2.47 1.83
fuelpos = 0.00 0.00 -0.00
waterpos = 0.00 0.00 0.00
lavatorypos = 0.00 0.00 0.00
engine1pos = -4.08 1.58 0.94
engine2pos = 4.08 1.58 0.94
engine3pos = 0.00 0.00 0.00
engine4pos = 0.00 0.00 0.00

[exit1]
remove = 1

[exit2]
remove = 1

[exit3]
remove = 1

[exit4]
pos = -0.80 -8.64 -0.59 0.00
code = 1
name = Main door
embeddedStair = 0

[service1]
remove = 1

[service2]
remove = 1

[cargo1]
pos = -1.09 6.42 -0.80 0.00
code = (A:FOLDING WING HANDLE POSITION,bool)
name = Cargo door
embeddedStair = 0
uldcode = AUTO

[cargo2]
remove = 1

[cargomain]
remove = 1

Title: Re: Flight1 ATR 72-500
Post by: doksas on October 10, 2019, 04:58:12 am

Here is config with working baggage, passengers and catering.
Catering is on left main passengers door, maybe little highest but i like truck ( no van )  catering .
Only not figure how to see big fuel truck, i set fuel point height to 3.50 but still i see small fuel truck, any help with big truck?

[aircraft]
nosegear = 8.84
refueling = 1
battery = 1
pushbackraise = 1
pushbackdummyevent = 0
iscargo = 0
trafficcones = 1
preferredexit =  3
wingrootpos = 1.35 -2.69 1.83
wingtippos = 13.44 -2.47 1.83
fuelpos = 8.50 -1.75 3.50
waterpos = 0.00 0.00 0.00
lavatorypos = 0.00 0.00 0.00
engine1pos = -4.08 1.58 0.94
engine2pos = 4.08 1.58 0.94
engine3pos = 0.00 0.00 0.00
engine4pos = 0.00 0.00 0.00

[exit1]
remove = 1

[exit2]
remove = 1

[exit3]
remove = 1

[exit4]
pos = -0.80 -8.64 -0.59 0.00
code = 1
name = Main door
embeddedStair = 0

[service1]
remove = 1

[service2]
pos = -13.71 -7.61 -0.21 178.50
code = 1
name = Service door
embeddedStair = 0

[cargo1]
pos = -1.09 6.42 -0.80 0.00
code = (A:FOLDING WING HANDLE POSITION,bool)
name = Cargo door
embeddedStair = 0
uldcode = AUTO

[cargo2]
remove = 1

[cargomain]
remove = 1