Products Support > GSX Support FSX/P3D
List of supported airplanes in GSX
XCLTM3:
--- Quote from: virtuali on September 04, 2013, 11:27:10 pm ---It's on the Live Update now. Force a check for updates in the Couatl menu, and it will download the updated files to support the PMDG 777
--- End quote ---
Umberto,
my system is suffering.
I've;
a) downloaded & installed the latest update 4 times
b) restarted FSX 4 times
c) even went in manually on the 3D editor and set up the cargo doors and passenger doors
d) the rear cargo loader still won't line up correctly with my 3D setting (even though the Front loader works fine now)
e) I still get a message from GSX that I need to "open exit 2" even though every door on the 777 (including cargo doors) are open????
Can you help me out here please???
Steve
virtuali:
--- Quote from: XCLTM3 on September 05, 2013, 09:01:05 am ---c) even went in manually on the 3D editor and set up the cargo doors and passenger doors
--- End quote ---
That's your problem: if you already tried to edit the configuration manually, the .cfg file you created always takes precedence over the GSX native support which is now being added.
You must Reset the config in the editor (or remove the .cfg file manually), otherwise you won't see the GSX updated support for the 777
XCLTM3:
--- Quote from: virtuali on September 05, 2013, 10:00:20 am ---
--- Quote from: XCLTM3 on September 05, 2013, 09:01:05 am ---c) even went in manually on the 3D editor and set up the cargo doors and passenger doors
--- End quote ---
That's your problem: if you already tried to edit the configuration manually, the .cfg file you created always takes precedence over the GSX native support which is now being added.
You must Reset the config in the editor (or remove the .cfg file manually), otherwise you won't see the GSX updated support for the 777
--- End quote ---
Umberto,
I'll happily reset the cfg.
However, what do you mean by "That's your problem"?
Did you read the series of steps I took before that? I would have liked a response for those too. Please don't handpick your responses. Look at all the issues raised and
respond accordingly. That's all I would expect from you and FS Dreamteam. I manually cfg the aircraft as a last resort, although I would have preferred not to.
Nothing seems to be working for me at my end no matter what I do. This is the 1st time I've had such an issue with getting GSX to work with an add-on aircraft. I just need to know "HOW CAN I GET IT TO WORK".
If I reset the cfg, and redownload & install for the 5th time, and it still doesn't work what is your suggestion?
Do you have a file I can manually install instead? I require some troubleshooting assistance and ideas.
Steve
virtuali:
--- Quote from: XCLTM3 on September 05, 2013, 10:36:15 am ---However, what do you mean by "That's your problem"?
--- End quote ---
Haven't you noticed I've QUOTED you, indicating what I've meant ? The "That's your problem" line was just below this quote:
--- Quote ---c) even went in manually on the 3D editor and set up the cargo doors and passenger doors
--- End quote ---
This means the "problem" I was referring to is that you used the editor, so the .cfg that has been created took precedence over the file in the Live Update.
--- Quote ---Did you read the series of steps I took before that?
--- End quote ---
Obviously yes.
--- Quote --- I would have liked a response for those too. Please don't handpick your responses. Look at all the issues raised and respond accordingly.
--- End quote ---
I replied to the only ONE step that would cause a problem. No need to reply to all of them.
Since, according to your report, you see the door referenced as "Exit 2", which is the generic name, it means the GSX file from the Live Update is not being used, because if it were, the main door should have been referenced as "L Entry 1", or the cargo doors should be called "Cargo FWD/AFT" same as they are in the PMDG FMC.
This is enough indication for me that a GSX.CFG file is taking precedence, so it must be Reset, or manually removed, as explained in the other thread I've linked, by removing the PMDG 777 folder in the %APPDATA%\Virtuali\Airplanes folder.
XCLTM3:
Umberto,
long before I tried to manually edit the cfg file, I downloaded & installed the updater 3 times & restarted FSX several times also. Nothing happened. No changes or recognition of the 777 by GSX.
This was not addressed.
Just to clarify things.
Navigation
[0] Message Index
[#] Next page
[*] Previous page
Go to full version