General Category > General Discussion
Flightbeam's San Francisco 2.0 screw up!
G.Bosak:
--- Quote from: virtuali on July 26, 2011, 06:28:14 pm ---
--- Quote from: G.Bosak on July 26, 2011, 06:25:47 pm ---FSX opened a dialogue to trust the coatl as usual, but the version is 2.0.0.2113. And this version doesn't work on my system too.
--- End quote ---
the Addon Manager will get whatever version is online the moment you run it. So, run the Addon Manager installer again, and you'll get the 2141.
--- End quote ---
i did it 10 minutes ago!? and it seems that coatl isn't updated as planned. Btw. the addon-manager is 2.8.0.3
virtuali:
--- Quote from: G.Bosak on July 26, 2011, 06:30:46 pm ---i did it 10 minutes ago!? and it seems that coatl isn't updated as planned.
--- End quote ---
Since I've uploaded it less than 10 minutes ago, that's fairly normal, otherwise I wouldn't said to run the installer again.
However, I said that was a problematic version, but it wasn't. The problematic version was 2135, the 2113 was an earlier version from June that I've uploaded so you could use the scenery while we fixed the problem with the new one.
We *have* fixed the problem with the new one, which is 2141 BUT, 2113 SHOULD run on your system, it was the version which was online for the latest 2 months and worked for everyone. Note that, it's NORMAL that a newly trusted module wouldn't run the FIRST time after it has been trusted so, you should exit from FSX after trusting it, wait a bit, and launch it again, it will work.
In any case, try with the current version anyway, and don't worry if it doesn't run on the *first* FSX run after being trusted.
G.Bosak:
--- Quote from: virtuali on July 26, 2011, 06:36:13 pm ---
--- Quote from: G.Bosak on July 26, 2011, 06:30:46 pm ---i did it 10 minutes ago!? and it seems that coatl isn't updated as planned.
--- End quote ---
Since I've uploaded it less than 10 minutes ago, that's fairly normal, otherwise I wouldn't said to run the installer again.
However, I said that was a problematic version, but it wasn't. The problematic version was 2135, the 2113 was an earlier version from June that I've uploaded so you could use the scenery while we fixed the problem with the new one.
We *have* fixed the problem with the new one, which is 2141 BUT, 2113 SHOULD run on your system, it was the version which was online for the latest 2 months and worked for everyone. Note that, it's NORMAL that a newly trusted module wouldn't run the FIRST time after it has been trusted so, you should exit from FSX after trusting it, wait a bit, and launch it again, it will work.
In any case, try with the current version anyway, and don't worry if it doesn't run on the *first* FSX run after being trusted.
--- End quote ---
now v2141 is installed, but i am sorry to say it doesn't work.
tested at:
KSFO
KORD
KLAS
KDFW
and i can exclude AV engines causing this, cause i don't use any ;D
enough of trial & error for today this is taking too much time, i feel like in mid-beta:-[
JPL19:
--- Quote from: virtuali on July 26, 2011, 06:36:13 pm ---...
We *have* fixed the problem with the new one, which is 2141 BUT, 2113 SHOULD run on your system, it was the version which was online for the latest 2 months and worked for everyone. Note that, it's NORMAL that a newly trusted module wouldn't run the FIRST time after it has been trusted so, you should exit from FSX after trusting it, wait a bit, and launch it again, it will work.
In any case, try with the current version anyway, and don't worry if it doesn't run on the *first* FSX run after being trusted.
--- End quote ---
Did not work for me.
Version is 2141, installed afer the post above. Same issue. Coutle Powered does not show in Add-ons. Installed as per directions, this is after an initial start then another start, then a re-boot. It is in the exe.xml, and, in the trusted section of fsx.cfg after re-start. I even removed all Trusted entries in my fsx.cfg to avoid conflicts on the first re-start.
It is not me or my system, I have at least 10 previous sceneries installed, including Hawaii II just in the last week w/o issue.
Joe
virtuali:
--- Quote from: G.Bosak on July 26, 2011, 07:01:08 pm ---now v2141 is installed, but i am sorry to say it doesn't work like the 2113 today.
--- End quote ---
You can try this, reinstall Hawaii airports 2 with the NETWORK DISCONNECTED.
This will use the Couatl version that was included in the installer, instead of the one that is online. This shouldn't be necessary, because as I've said, the 2113 version was 2 months old, and it always worked.
BUT, at least, you can verify with the version that DID run on YOUR system until today, otherwise you wouldn't be able to ever see Hawaii 2 in the first place. If the version that was included in the Hawaii2 installer doesn't run, it's clearly a problem with your system that happened today, because it can't obviously corrupt itself when it's inside the installer you downloaded days ago, and it worked.
Navigation
[0] Message Index
[#] Next page
[*] Previous page
Go to full version