General Category > General Discussion
Flightbeam's San Francisco 2.0 screw up!
duckbilled:
Hello there. Thank you for all the hard work on this issue but unfortunately things are not working out for me and I am getting a little annoyed. 1 hour ago, I had a SFOv1 and LSZH that worked. Now neither work. If there is really a fix for this issue, it needs to be posted in one sticky - one post, no comments with 1, 2, 3 steps. Done venting.
Problems:
1. SFO has a concrete barrier and a crane in T2 but gates and AI appear at T2 (I know, this is a FB issue but I am waiting on authorization on their forums).
2. When I load LSZH, it is unflyable. I get great performance (with buildings) for 5 seconds and then a complete pause for 20 seconds. The start/stop continues until I switch to a different airport or close the sim.
What I did:
1. I already had SFOv1. I didn't not try to update it until the problem was resolved. I followed the advice in this thread (http://www.flightbeam.net/forums/viewtopic.php?f=4&t=209) to download and install the file ksfo_fsx_setup.exe. I started the sim and found the concrete barrier and the crane at T2 along with the T2 gates and AI.
2. I took the advice in this thread to put the bglmanx_fbeam.dat in the root FSX folder and the pye file in the FSDT\Zurich\couatl\ZurichX. Now I get these terrible pauses at LSZH. They are very similar to the pauses you get from UT2 when it injects traffic. Those pauses, however, only happen once. The new LSZH pauses happen every 5 seconds. Makes me think simconnect is trying to do something, not succeeding and trying to do it again over and over again.
What did I do wrong?
cmpbllsjc:
Jeff,
Tonight I updated KSFO and LSZH both to versions 2.0 and it worked fine. Here's what I did. Make sure your ORBX panel is at Default just to be safe.
1. Go to addon/remove programs and uninstall both KSFO and LSZH (if you have LSZH)
2. Open the scenery.cfg and make sure that the installer removed both entries, which it did but left a gap in layer numbers.
3. Installed both KSFO 2.0 and SFO 2.0
4. Opened the scenery.cfg with scenery cfg editor and placed them back in the spots where they originally were and renumbered to get rid of the gaps.
5. Tested both in FSX and each worked fine.
Also I tried LAS, ORD, DFW, etc. and all worked fine for me.
Maybe you should try this method and see what happens while you wait for Umberto to reply.
virtuali:
--- Quote from: duckbilled on July 29, 2011, 06:06:16 am ---2. I took the advice in this thread to put the bglmanx_fbeam.dat in the root FSX folder and the pye file in the FSDT\Zurich\couatl\ZurichX. Now I get these terrible pauses at LSZH.
--- End quote ---
That advice is now not needed anymore, since Zurich has been just updated to 2.0 version.
If you use Zurich 2.0, there's no need to replace that file and, in fact, it will cause problems, because it came from Zurich 1.5.2 and it will probably result in missing objects and/or pauses. Instead, if you use Zurich 1.5.2, you have to use that .pye file.
Basically, using the installers that are online now, all the manual file-replacements suggestions discussed in this thread, are not needed anymore and, in fact, could cause problems.
duckbilled:
Thanks Sean. It does seem logical that one would uninstall the old version and install the new version. Unfortunalty, the instructions over at FB don't specify that.
Bruce Hamilton:
--- Quote from: duckbilled on July 29, 2011, 04:00:22 pm ---It does seem logical that one would uninstall the old version and install the new version. Unfortunalty, the instructions over at FB don't specify that.
--- End quote ---
Why would they? I've always installed my updated sceneries over itself with no problems. Unless its a scenery that requires uninstalling, why waste the time?
Navigation
[0] Message Index
[#] Next page
[*] Previous page
Go to full version