Products Support > GSX Support FSX/P3D

GSX causing FAILURES in PMDG 737 NGXu during pushback

<< < (2/3) > >>

Captain45:

--- Quote from: virtuali on December 11, 2023, 10:23:25 pm ---You are reporting two very different issue:

- the airplane disabled after pushback. While it only occurred after exiting the pushback, and this is surely fixed, I must say this has been tested to be fixed in MSFS only, we never tried it on FSX/P3D, so we'll check this.

- the airplane shakes if it's pushed while it's raised. This will be fixed in the next update and, again, it's a P3D-specific issue happened because we haven't fully tested it in P3D.

--- End quote ---

Correct. If you wait long enough for the pushbacktruck to park then there is no problem. Not in P3D also.
Well... the shaking (with the PMDG737) after the raise might need some testing in P3D. It worked fine before the last update.

Thanks for sorting this out Umberto. I'll wait for the update and leave the box unchecked for a while.

Captain45:

--- Quote from: virtuali on December 11, 2023, 10:23:25 pm ---- the airplane disabled after pushback.

--- End quote ---

We ar not done yet on the subject of the aircraft stays locked after pushback!

OK, I know I have to wait until the tug is parked. But...
If you release the parkingbrake just after "Left is clear, right is clear" (because I check the rudder which makes P3D to release the parking brake), you get a warning to set the parkingbrake immediately. If doing so, the aircrafy stays locked, the "Have a good flight (or something)" does NOT come, and there is no way to let the aircraft start taxiing. Not even after a Couatl restart. You have to start the flight all over again, because the GSX Menu is in 'after landing mode' and you cacn only select a gate or the RWY for departure (and warp to it) which still keeps the aircraft locked in place.

May I suggest to solve this and/or unlock the aircraft after L & R are clear.

Captain Kevin:

--- Quote from: Captain45 on December 13, 2023, 02:47:45 pm ---(because I check the rudder which makes P3D to release the parking brake)

--- End quote ---
Just to be clear, this isn't a P3D issue, but chances are, when you checked the rudder, you may have somehow tapped the brakes, which would release the parking brakes. I've never had an issue with the parking brakes being released when checking the rudder.

Captain45:

--- Quote from: Captain Kevin on December 14, 2023, 02:44:05 pm ---Just to be clear, this isn't a P3D issue, but chances are, when you checked the rudder, you may have somehow tapped the brakes, which would release the parking brakes. I've never had an issue with the parking brakes being released when checking the rudder.

--- End quote ---
Correct. Never had this with the QW787, but in the PMDG 737NGXu, as soon as I touch the rudderpedals, the parkingbrake is OFF. I think I have to adjust the FSUIPC settings a bit to avoid this problem.

I installed the update that shold have solved the shaking problem after the Raise yesterday Dec. 14th. So today I cheked the box for the Raise and guess what? The problem is NOT solved. What I do notice, is that the Raise is very high. A lot higher than before this feature was implemented (2 updates ago).

Captain Kevin:

--- Quote from: Captain45 on December 15, 2023, 02:05:45 pm ---Correct. Never had this with the QW787, but in the PMDG 737NGXu, as soon as I touch the rudderpedals, the parkingbrake is OFF. I think I have to adjust the FSUIPC settings a bit to avoid this problem.

--- End quote ---
I'd still say that's something within your settings because I fly the PMDG 737, 747, and 777, and I don't have this problem with any of them. I do have a slight null zone, so perhaps that's something you want to look into.

Navigation

[0] Message Index

[#] Next page

[*] Previous page