Products Support > GSX Support FSX/P3D
Problems after Pushback
flyerone:
--- Quote from: virtuali on November 27, 2023, 05:14:59 pm ---
--- Quote from: flyerone on November 26, 2023, 02:24:03 pm ---Which means that they just checked and fixed the quickedit but not the normal left and right pushback.
--- End quote ---
No, it means Left/Right never had any problem to begin with, the bug which lasted only a few days, was only related to QuickEdit (or even pre-created Custom Pushback, anything the involved the Editor), it couldn't possibly happen in a normal Left/Right pushback so, either the problem doesn't happen in Left/Right, or it's a completely different problem, so I really need a new accurate report.
To clarify better: the problem was because the whole simulation wasn't re-enabled back after *exiting* the Pushback Editor, because the QuickEdit sequence has been moved later, which caused controls not working or engines not starting, which is what has been reported in the first post. This specific issue can't possibly happen anywhere else than on exit the Pushback Editor.
--- End quote ---
Ok I’m just back at home after work. Today or tomorrow I’ll upgrade gsx than I’ll test it and I’ll let you know.
Joggu:
Unfortunately, the problem still exists after the newest GSX-update.
Here again a short summary:
- The problem only occurs with the towbarless pushback vehicle
- The airplane does not move till you reset GSX or it reset itself after some time
- The pitch trim cannot be adjusted till you reset GSX or it reset itself after some time
- I don't use Quick-Edit-Pushback
- I don't use pushback-raise
- I use the FSLABS A320
- I use P3D V5.4
Please fix this problem as soon as possible!
Regards
Joël
flyerone:
--- Quote from: Joggu on December 14, 2023, 05:52:52 pm ---Unfortunately, the problem still exists after the newest GSX-update.
Here again a short summary:
- The problem only occurs with the towbarless pushback vehicle
- The airplane does not move till you reset GSX or it reset itself after some time
- The pitch trim cannot be adjusted till you reset GSX or it reset itself after some time
- I don't use Quick-Edit-Pushback
- I don't use pushback-raise
- I use the FSLABS A320
- I use P3D V5.4
Please fix this problem as soon as possible!
Regards
Joël
--- End quote ---
I tested the quickedit which I use most of the time, with pushback-rise and works fine now.
It’s pretty weird that they didn’t solve the other pushback bug as you’re reporting Joggu. They said the problem was only with quickedit but, as you’re saying, I think they didn’t check the other pushback options.
kholt:
I don’t know if my issue is the same or not. I only do regular left/right pushback. Sometimes the aircraft won’t move afterwards. My workaround is to manually “set” the chocks and then remove them again. For some reason toggling them on and off after pushback allows the a/c to move short of applying toga thrust and hurtling off the apron and into the grass….
This is with the FSLabs A320 and P3D v5.4.
DaveT:
--- Quote from: anirbinna on November 01, 2023, 08:58:05 pm ---
--- Quote from: Joggu on October 29, 2023, 08:02:03 am ---Hi,
Since one of the last GSX-updates I have some problems after the pushback with the FSLABS Airbusses in P3D V5.4 (other aircraft i don't have tested).
- After pushback you cannot set the pitch trim and moving/rolling till you reset GSX or GSX disappears by itself
- The problem occurs only with pushback truck without towbar (towbarless)
As I have seen in the FSLABS-Forum there are also some others with the same problem.
Regards
Joël
--- End quote ---
I can confirm i am having the same issue .Please fix the issue as soon as you can
--- End quote ---
I also confirm the same issue with same aircraft.
Navigation
[0] Message Index
[*] Previous page
Go to full version