Products Support > GSX Support FSX/P3D
Unable to edit service vehicles
virtuali:
--- Quote from: Papacoach on February 17, 2022, 02:37:51 pm ---Good morning. After an update and reboot this morning I no longer have the issues I was facing yesterday. The only other change in the system yesterday was installing the latest active sky, which did run a VC++ redistribution or two.
--- End quote ---
That's to be expected. When a new version of the VC++ redistributable is installed, a reboot is almost always required, because the redistributable installers delayed the final stage of the setup to the *next* reboot, because some files couldn't be updated while Windows is running, so the redistributable installation is not complete until then.
And yes, since our software ( like any other Windows software ), depends entirely from the VC++ runtime libraries, it will likely fail if there's any issues with those.
renzomarcus:
--- Quote from: virtuali on February 17, 2022, 02:43:11 pm ---
--- Quote from: Papacoach on February 17, 2022, 02:37:51 pm ---Good morning. After an update and reboot this morning I no longer have the issues I was facing yesterday. The only other change in the system yesterday was installing the latest active sky, which did run a VC++ redistribution or two.
--- End quote ---
That's to be expected. When a new version of the VC++ redistributable is installed, a reboot is almost always required, because the redistributable installers delayed the final stage of the setup to the *next* reboot, because some files couldn't be updated while Windows is running, so the redistributable installation is not complete until then.
And yes, since our software ( like any other Windows software ), depends entirely from the VC++ runtime libraries, it will likely fail if there's any issues with those.
--- End quote ---
I just did a full restart of my system just in case, but you can see that when I change the tug location, it jumps back after going back into edit mode. It does not save the location at all.
You can't see me click in the GSX config window, but you get the idea.
Please do not gigve me the answer that it works for you. You can clearly see it does not for me, all of the runtimes that are required by GSX are installed.
Kind regards,
Renzo
virtuali:
--- Quote from: virtuali on February 17, 2022, 02:43:11 pm ---You can't see me click in the GSX config window, but you get the idea. Please do not gigve me the answer that it works for you. You can clearly see it does not for me, all of the runtimes that are required by GSX are installed.
--- End quote ---
Of course I'll give you the answer that it works for me, because that's a clear indication the problem is NOT GSX.
Looking at your video, I can see there's ANOTHER application that is interfering, that green line that says "Entering Slew Mode - recalculating data..." which appears very briefly when you Enter Slew and appears again when you Exit Slew is NOT coming from GSX!
I don't know what that is but, depending how it's made, it seems to have intercepted the Enter/Exit in Slew mode and, I can see the Exit interception might cause issue, since GSX needs to know when you Exit Slew to save the .INI file.
Try to disable it and see if GSX can save now.
renzomarcus:
That message was caused by the FSLabs aircraft.
While that has never given me any issues, I quickly launched in a P3D default aircraft for the sake of troubleshooting.
As you can see, the result is the same. Also when changing from on stand to another and back, the saved location is gone.
Curiously, please note that when I adjust the marshaller, that IS saved.
https://youtu.be/MZAYu2tZ5z8
virtuali:
--- Quote from: renzomarcus on February 18, 2022, 12:51:41 am ---Curiously, please note that when I adjust the marshaller, that IS saved.
--- End quote ---
I'm sorry, but I can only repeat and confirm the problem doesn't happen, and I took the time to both testing it, and posting a video to show it works. Also, nobody reported this problem, and people are sharing their customization with Walk-in gates so, clearly, it doesn't work "only for me", but it works for everybody, except you.
Are you SURE you have run the FSDT Live Update so you have the latest version ? We had a problem with the GSX Apply button not working, but this was only in the first release of this update, it has been fixed, and multiple users confirmed it was fixed.
Navigation
[0] Message Index
[#] Next page
[*] Previous page
Go to full version