Products Support > GSX Support FSX/P3D

Pallets separated by size?

(1/2) > >>

p3dx3:
Are the different numbered pallets you can assign separated by size of the pallets? The cargo doors I am assigning pallets is too small for the pallets being called. I want small pallets is there a way to do this thanks?

Captain Kevin:
I don't think so, I think those pallets just have different things on them if I remember this correctly. Unfortunately, I'm in the office, and I don't go home until March, so I can't check for you. Best way to check is to go to the aircraft customization, manually select each pallet, and test it out.

CaptainSazzman:

--- Quote from: p3dx3 on February 12, 2021, 04:22:26 am ---Are the different numbered pallets you can assign separated by size of the pallets? The cargo doors I am assigning pallets is too small for the pallets being called. I want small pallets is there a way to do this thanks?

--- End quote ---

Easy. Go to AppData/roaming/virtuali/airplanes and look for the specific aircraft you are editing. In the ULD code section, enter the code for the type of pallet you want. The types of pallets and their codes can be found in the GSX manual. See the example below from a 747-8

//////////////////////////////////////////////////////////////////////////////////////////////////
[cargo1]
pos = 2.01 20.48 -1.02 0.00
code = (L:7X7XforwardcargoDoor,number) 990 >=
name = FWD Cargo
embeddedStair = 0
uldcode = AKC,AKE,ALP

[cargo2]
pos = 2.01 -16.98 -1.01 0.00
code = (L:7X7XaftcargoDoor,number) 990 >=
name = AFT Cargo
embeddedStair = 0
uldcode = AKC,AKE,ALP

[cargomain]
remove = 1
//////////////////////////////////////////////////////////////////////////////////////////////////

p3dx3:

--- Quote from: CaptainSazzman on February 14, 2021, 12:49:25 am ---
--- Quote from: p3dx3 on February 12, 2021, 04:22:26 am ---Are the different numbered pallets you can assign separated by size of the pallets? The cargo doors I am assigning pallets is too small for the pallets being called. I want small pallets is there a way to do this thanks?

--- End quote ---

Easy. Go to AppData/roaming/virtuali/airplanes and look for the specific aircraft you are editing. In the ULD code section, enter the code for the type of pallet you want. The types of pallets and their codes can be found in the GSX manual. See the example below from a 747-8

//////////////////////////////////////////////////////////////////////////////////////////////////
[cargo1]
pos = 2.01 20.48 -1.02 0.00
code = (L:7X7XforwardcargoDoor,number) 990 >=
name = FWD Cargo
embeddedStair = 0
uldcode = AKC,AKE,ALP

[cargo2]
pos = 2.01 -16.98 -1.01 0.00
code = (L:7X7XaftcargoDoor,number) 990 >=
name = AFT Cargo
embeddedStair = 0
uldcode = AKC,AKE,ALP

[cargomain]
remove = 1
//////////////////////////////////////////////////////////////////////////////////////////////////

--- End quote ---

the pallets I am looking to use only small pallets not ULDs

virtuali:

--- Quote from: p3dx3 on February 12, 2021, 04:22:26 am --- I want small pallets is there a way to do this thanks?
--- End quote ---

Their number is not a direct indication of the size. I suggest setting only one kind, look at it, then switch to another one, so you'll know which one is which, after 8 tries.

Navigation

[0] Message Index

[#] Next page